Application:

These permanent magnetic chucks are designed for securing works of materials having a relatively weak magnetic property such as cemented carbide during grinding.

They are normally mounted on and held by other chuck for use.

Features:

*The use of a powerful rare earth magnet ensures a sufficient holding power even on cemented carbide materials.

Application:

These permanent magnetic chucks are designed for securing works of materials having a relatively weak magnetic property such as cemented carbide during grinding on small grinders.

They are secured to the T-grooves on the grinding table with clamps for use.

Features:

*A special mechanism allows change over (ON/OFF) of the magnetic force without causing a loss of magnetic force and without requiring a large operating force.

*The use of a powerful rare earth magnet ensures a sufficient holding power even on cemented carbide materials.

Application:

*Most suitable for grinding operation.

Features:

*Handle can pivot outward approx. 10°.

Application:

Used for dressing grinding wheels.

Features:

*Powerful type with attraction of 80kgf.

*Dresser can be mounted in angle.

*Magnet is easily mounted/removed just by a changeover handle operation.

*Dresser clamp can be mounted on the upper face of magnet.

Application:

Permanent magnetic chuck with high performance magnet for grinding operation on rotary grinders, cylindrical grinders, internal grinders, and for cutting operations when mounted on a lathe.

Features:

Type 2 chuck, with variable holding:

Position and lock part with light holding, then, after fine adjusting to the exact position, lock down with full magnetic force.

*Powerful chuck with minimum residual magnetism.
Suited for both grinding and cutting operations.

*Especially excellent for machining thin workpieces, and thick work as well.

*Lowest profile height;only 55mm.

*High precision chuck, with minimum change.

*On to OFF rotation in 130°.

Application:

These chucks are suitable for securing work-pieces in electro discharge machining.

Features:

*Can be used in fluid.

*With extra powerful holding, these chucks are suited to be used in applications where conventional, standard chucks cannot.

*A jetting hole is provided in the center for flushing and removal.

*The bottom face is made flat to allow tapping and clamping.

*Counter boring around the jet holes on the attractive face is possible.

*Improved water-tightness.

Application:

Most suitable for grinding applications, from small to large and thin to thick.

Features:

*Thin profile:43mm to 60mm.

*Fine spaced pole pitch;sub-micro-pitch model.

*Light pressure on the hexagonal wrench key, changes the OFF to ON in half a turn.

Application:

These permanent magnetic chucks can be mounted on the index table of grinders to repeat the same grinding work. They can also be used as a jig to feed works to profile grinders.

They come either two-faced or four-faced.

Features:

*The magnetic force can be turned ON and OFF individually oneach face. Thus, works can be ground and mounted/demounted alternately at the same time to improve the work efficiency.

*Works are held by the magnetic force. Thus, no mechanical clamps are necessary, work mounting and demounting is easy and there is no fear of damaging workpieces.

*The magnetic force ON / OFF handle is removal so that it will not obstruct the grinding work.

Application:

This is our latest permanent magnetic chuck designed for a wide range of application. Its increased attractive forces strengthen the holding power for heavy grinding and light cutting operations.

Features:

*Provides powerful holding power for the thinner work piece as well as for the thicker work piece.

*This is the thinnest profile chuck of its type, with height of only 50 mm.

*Specially designed to minimize face plate precision variation when switched on, providing a higher degree of accuracy on your finished work piece.

Application:

These chucks are designed for securing work-pieces during electric discharge machining.

Features:

*Can be used in fluid.

*With extra powerful holding, these chucks are suited to be used in applications where conventional, standard chucks cannot.

*A jetting hole is provided in the center for flushing and removal.

*The bottom face is made flat to allow tapping and clamping.

*Counter boring around the jet holes on the attractive face is possible.

*Improved water-tightness.

Application:

Suitable for angle-grinding on the grinder.

Features:

*The graduated rotary shaft makes it easy to grind at any angle.

*The chuck mounts easily and securely to ensure high precision work.

Application:

Best suitable for holding workpieces on electric discharge machines.

They can also be used for grinders.

Features:

*Very low profile and light weight.

*They can be used on grinders by placing auxiliary iron plates on both sides of workpieces (size 20 x t1 or over).

*Residual magnetism is minimal for easy removal of workpieces.

*The handle can be operated lightly. The handle (hexagonal wrench) is inserted to the top surface for operation without dipping your hand in liquid.

Application:

This chuck is designed for holding thin, thick and small workpieces in grinding operation, and also can be used for electro discharge machining .

Features:

*Extremely low profile, 40mm for small sized and 50mm for middium sized chucks. Light weight.

*Wide holding area.
Smooth and light ON/OFF operation, removal handle.

*Easy work-piece positioning by using weak holding power since handle can be turned to any position.

Application:

Suitable for grinding and electro discharge machining from thin to thick and small to large workpieces.

Features:

*Effective for thin or small workpieces since pole pitch is very fine.

*Chuck mounting face is magnetic so that mechanical clamping is not needed.

*It also can be used in liquid.
Removable handle.

Application:

These chucks can be used for a wide range of applications including securing very small workpieces and workpieces during grinding, electric discharge machining and wire cutting. They can be used in fluid.

Features:

Compared with Model RMWH-B, these chucks are capable of holding thinner and smaller workpieces.

Application:

These chucks are suitable for securing workpieces during electric discharge machining.

Features:

*Can be used in fluid.

*The use of fine pole pitches works very well with thin and small workpieces.

*The bottom is made flat to allow tapping for clamping metal.

*Water-tightness has been improved from the standard type.

Two types are available such as lengthy type (Model SBP-R713S) and breadthy type (Model SBP-R713L) as seen to the tilting angle.

Excellent precision and durability similar to thin type permanent magnetic sine bar chuck, but overall height is slightly higher.

Application:

Easily usable for angle-grinding for high precision on the mold grinder, etc.

Features:

*Thin type permanent magnetic chuck is applied.

*Polar pitch on the work face is shortened to 1.5 mm from conventional 10 mm so as to meet the grinding work of wide range from small pieces to thick work.

Application:

This is a long-type permanent magnetic chuck with the shorter side as tilt axis, which ensures high-precision grinding and measurement. This is suitable for high-precision angle grinding on a mold grinding machine and so on.

Features:

*A handle facilitates work tilted in the longitudinal direction.

*The functional features and performance conform to the wide-type.

Effective area of double type sine bar chuck is enlarged by employing the thin type permanent magnetic chuck. This increases the range of types usable by tilting works in length, breadth or composite angle.

Features:

*Each part is designed to withstand the use for longer period in high precision finish within 0.007 mm same as single type.

Application:

Designed for easy use in mold-grinding and angle measurement of small works.

Features:

*Compact and simple in construction for easy handling.

*The shaft can be secured so as to use it for grinding operation.

*Usable as sine bar by removing the pemranent magnetic chuck from chuck base.
Eesy to clean up.

Application:

Flat type for wide range of uses in height so thin as 81mm~106 mm. This single type chuck is finished in high precision within 5 micron by mounting thin type permanent magnetic chuck.

Entire sine bar section is made of special steel and ground in precision after hardening it.

High precision grinding and measurement is ensured for longer periods due to lapping finish of principal sections.

Features:

*New type with thin permanent magnetic chuck.

*Easy to use and a large effective area is provided for machining the works.

Dust-proof cover with duplex construction is employed. This feature prevents chip from sticking onto the gauge block. Operation is made with the cover closed.

Application:

Sine bar chuck suitable for grinding mold and high precison angling of jig, etc.

Features:

*Chuck is easily operated with smooth tilting ability.

*Clamp system is used to set delicate angle with one-touch operation.

*Lever can change position slightly by pulling it to the shaft direction.

*Dust-proof cover is fixed at any desired place. This makes it easier to clean the gauge block atand, etc.

*Duplex construction of dust-proof cover allows operation with the cover closed and prevents chips from mixture even if the gauge block is set.

*Gauge block of JIS, B grade, 40mm, is supplied as accessories.

Application:

The SKM is designed for applications requiring a vertical holding magnetic surfaces.

Used when it is not possible to set the part for holding in a conventional magnetic chuck, and when additional vertical force is needed to secure
work.

Features:

*The permanent magnetic chuck used in the SKM is our powerful RMT, rare earth magnetic chuck.

*Holds various sizes work parts;thin, small, and thick.

Features:

Versitile and effective both iron and nonmagnetic works can be held by using the magnetic and mechanical clamps.